- Antimicrobial copper alloy base
- Stainless steel metal lid (water chamber)
- Water inlet tap (Screws into the base (1) with Teflon tape on the thread)
- Metal coupling clamp. (First pass it through the hoses (5 and 11) and screw it tightly to the inlet and outlet nozzles (3 and 9) after having previously installed the hoses (5 and 11)
- Plastic hose 1/4″ (connects to nozzles 3 and 9 respectively)
- Metal connector clamp for flexible hose (5) with tap (7) (first pass the clamp through the hose (5) and screw)
- 1/4″ water supply tap to the filter (connects to the cold water) put Teflon or hemp on the thread and connect it to the nipple (8)
- Nipple (T-distributor) for supplying water to the kitchen tap and to the filter. (Put Teflon tape on the thread and connect it to the power supply).
- Outlet tap for filtered water to the faucet (Screwed into the base (1) with Teflon tape)
- Metal connector retainer
- Plastic hose 1/4''
- Metal nozzle for connecting to the tap (pass it through the hose (11))
- Plastic wedge (insert it into the plastic hose (11) for reinforcement)
- Plastic conical sealing cylinder (nipple) (pass it through the hose (11))
- Metal nut for attaching the faucet (screws all the way onto the faucet thread to stabilize the faucet at the bottom of the sink)
- Serrated metal washer (grower) for securing (placed under the plastic washer (17))
- Plastic support washer (placed under the sink)
- Rubber sealing washer (placed under the sink)
- Rubber sealing washer (placed above the sink)
- Oval metal crane support base (remove the blue nylon protective cover)
- 21.Stainless steel swivel faucet.
- Ceramic filter – replacement filter cartridge (screws into the center of the metal base of the device)
- Large rubber sealing washer between the metal base (1) and the metal cover (2)
- Antimicrobial Copper alloy disc (installed), to kill microbes
Operating parameters.
-Maximum working pressure: 7 BAR
-Operating temperature: 38about C(100about F)
-Minimum operating pressure: 1 BAR (Reduced flow rate) – Recommended operating pressure: 3 – 7 BAR
-Minimum operating temperature 5oh C(41about F).
– Recommended filter flow rate for perfect filtration 1.5 – 2.5 liters/minute at 3 – 3.5 BAR network pressure
ORDER OF INSTALLING THE SPARE CASSETTES FOR THE DOUBLE OR TRIPLE FILTER
IMPORTANT: Place the inlet (3) and outlet (9) taps in the base or bases and wrap Teflon tape (not included) on their threads to avoid possible water leaks.
❶INSTALLATION (The responsibility for the correct and safe installation of the filter lies with the customer)
The filter should be placed upright under the sink, close to the water supply, and its tap should be placed in the desired location on the sink. Cut the 2-meter hose included in the package into 2 parts of such a size that you can pull the appliance out of the cabinet when changing the filter. (If the hose is cut crookedly, you will have a leak).
❷ ATTENTION
Make sure the water inlet to the filter follows the direction of the arrow, at the bottom of the metal base (1) of the appliance (see figure 1). AIf connected backwards, the ceramic cartridge will become clogged or broken..
PLACEMENT OF THE HANDLE ON THE SINK
– Drill a hole with a diameter of 11mm (millimeters) in the sink at the desired location for the tap (21) (first drill with a 6 millimeter drill bit).
– Before placing the faucet on the sink, first pass the nickel metal base (20) through its pipe, after peeling off the nylon protective coating, and pass the larger black rubber sealing washer (19) under it.
– Place the faucet in the hole you drilled on the sink, and on the part of the faucet that is located at the bottom of the sink, place the accessories (18), (17), (16) in the order shown in the drawing and screw the metal nut (15) all the way in to seal and secure the faucet to the countertop.
– Thread the metal clamp (10) onto one end of the hose (11). Connect the hose (11) to the outlet nozzle (9) and screw the metal clamp (10) securely.
– On the other end of the hose (11), first insert the metal tip (12), then the oval plastic cylinder (nipple) (14) and then insert the plastic wedge (13) inside the plastic hose to stabilize the nipple (14) in place. Screw the metal tip (12) securely onto the thread of the tap stem.
– Screw the cartridge (22) into the filter base (1) (loosely), without tightening it too much so that it doesn't break its plastic thread or ceramic filter, or the water flow rate may decrease.
– Screw the metal cover of the appliance (2) securely onto its base. Now open the tap and from the filter tap, the first time, some black water may come out from rinsing the activated carbon.
3. ATTENTION: The first time and each time you change the cartridge, let the water run for 10 minutes. Do not use the filter for 24 hours. After the 24 hours, let it run for 2-3 minutes and the filter is ready for use. Also, if the filter is left unused for more than 3 days, let the water run for 2-3 minutes.
4. ATTENTION: Only cold water should be used through the filter. If you use hot water, the binding and sealing materials on the cartridge will come loose, resulting in sediment, mud, rust, as well as chemical elements in the water, such as chlorine, etc., not being retained by the filter.
5. FILTER (CARTRIDGE) REPLACEMENT When replacing or cleaning the ceramic cartridge, it is a good idea to make sure that any cuts or wounds on your hands are covered to avoid contact with any germs that may have settled on the outside of the ceramic filter and that the antimicrobial copper in the base has not yet been able to destroy, as it takes about 2 hours to destroy them. Otherwise, follow the same procedure for replacing the cartridge as when you first installed the filter.
To unscrew the metal cover (2), first turn off the water supply to the filter and at the same time open the filter tap (21) on the sink to release the pressure and make it easier to unscrew the metal cover (2).
Interrupt the water supply to the filter when you want:A) Complete water cut-off to the filter.
B) Cleaning the cassette.
C) Changing the cartridge.
D) When you are away from home for days.
6. MAINTENANCE – CLEANING THE CERAMIC CASSETTE
Every 3-4 months or whenever the water flow rate decreases noticeably from the appliance tap (which means that the ceramic filter cartridge has become "clogged" with sediment, rust, mud, silt, limescale, etc.), remove it from the appliance and rinse it with cold water under the tap (without detergents), scrub it well over the entire surface with the wire part of the dish sponge, or with a harder wire material, or even with sandpaper (number 80) to clean it and improve the water flow. After rinsing it well, put it back in its place.
7. RECOMMENDED FILTER FLOW – TIME TO REPLACE SPARE CARTRIDGES
IMPORTANT: The highest filter efficiency is achieved when the water flow rate through the filter does not exceed 1.5 to 2 liters per minute. The cartridge capacity is for 14,000 liters of water or for 10-12 monthswhichever occurs first. The cartridge life may be reduced in cases of networks loaded with impurities such as mud, rust, silt, soil, limestone, etc., or in periods of drought when the load on the water supply networks is very high (due to low water levels). In these cases, the filter should be cleaned much more frequently and replaced earlier if, despite cleaning, the water flow rate in the appliance tap is not restored.
But regardless of the number of liters of water that will pass through the filter, you MUST replace the cartridge every 10-12 months at the latest, because from the moment it gets wet, its materials weaken month after month and the water that passes through the filter will pass unfiltered.
8. ANTIMICROBIAL DISC AND BASE MAINTENANCE
On the surfaces of the antimicrobial copper alloy materials, and more specifically inside the base (4) and the disc (6) located therein, a superficial discoloration may occur due to the natural oxidation of the antimicrobial copper, deposits of various materials coming from the water supply networks, such as rust, mud, etc. In these cases, these deposits, which in no way burden the overall operation of the filter, are good, both for aesthetic reasons and for reasons of cleanliness of the filter chamber, be removed in the following way:a) Clean both surfaces of the antimicrobial disc thoroughly with something harder like a potholder, coarse sandpaper, etc. b) Clean the inside of the antimicrobial base in the same way to remove any deposits that look like rust.
9. METAL APPLIANCE CLEANING PROCEDURE:
Wipe the appliance with a soft cloth slightly dampened with lukewarm water. Avoid using bleach or any chemical detergent or bleaching agent, or wire cloths as they will leave marks on the metal surface of the appliance.
10. IMPORTANTTo protect your filter, after each water supply interruption, open the MANDATORY First let your tap run for a while before using the filter.
11.ATTENTION The OLYMPUS+ water filter is designed for waters that are controlled by Municipal or Local Authorities and are fit for human consumption.
12. ATTENTION TO WATER PRESSURE
If the mains pressure is high, install a water filter before pressure reducer. But whether the mains pressure is high or low, put mandatory check valve (available at plumbing stores), so that in the event of a sudden increase in network pressure or a momentary water hammer phenomenon, to avoid breaking the hoses or the filter unit and causing flooding. When you are away from home for days, you should always close the water supply tap to the filter.
View product instructions in pdf format by clicking here.
